----------------------------------------------------------------------------- This file is a supplement to README.arcnet. Please read that for general driver configuration help. ----------------------------------------------------------------------------- Because so many people (myself included) seem to have obtained ARCnet cards without manuals, this will be a quick listing of all jumper settings I can find. Please e-mail apenwarr@tourism.807-city.on.ca with any settings for your particular card. Even if your ARCnet model isn't listed, but has the same jumpers, please e-mail me to say so. If your model isn't listed, and has different settings, PLEASE PLEASE tell me. I had to figure mine out without the manual, and it WASN'T FUN! Cards Listed in this file: Manufacturer Model # Bits ------------ ------- ---- SMC PC100 8 SMC PC110 8 SMC PC120 8 SMC PC130 8 SMC PC270E 8 SMC PC500 16 SMC PC500Longboard 16 SMC PC550Longboard 16 SMC PC600 16 Puredata PDI507 16 CNet Tech CN120-Series 8 CNet Tech CN160-Series 16 No Name -- 8/16 ** SMC = Standard Microsystems Corp. ** CNet Tech = CNet Technology, Inc. The model # is listed right above specifics for that card. Don't forget to read "quick briefing" first, since it applies to all ARCnets. Unclassified Stuff ------------------ - Please send any other information you can find. - And some unknowns (other info is welcome!): From: root@ultraworld.xs4all.nl (Timo Hilbrink) To: apenwarr@tourism.807-city.on.ca (Avery Pennarun) Date: Wed, 26 Oct 1994 02:10:32 +0000 (GMT) Reply-To: timoh@xs4all.nl [...parts deleted...] About the jumpers: On my PC130 there is one more jumper, located near the cable-connector and it's for changing to star or bus topology; closed: star - open: bus On the PC500 are some more jumper-pins, one block labeled with RX,PDN,TXI and another with ALE,LA17,LA18,LA19 these are undocumented.. [...more parts deleted...] --- CUT --- Quick Briefing: --------------- All ARCnet cards should have a total of four different settings: - the I/O address: this is the "port" your ARCnet card is on. Probed values, as of v0.14, are only from 0x200 through 0x3F0. (If your card has additional ones, which is possible, please tell me.) This should not be the same as any other device on your system. Supposedly MS Windows prefers values of 0x300 or more, eating net connections on my system otherwise. - Avery's favourite: 0x300. - the IRQ: on 8-bit cards, it might be 2 (9), 3, 4, 5, or 7. on 16-bit cards, it might be 2 (9), 3, 4, 5, 7, or 9-15. Make sure this is different from any other card on your system. Note that IRQ2 is the same as IRQ9, as far as Linux is concerned. - Avery's favourite: IRQ2. - the memory address: Unlike most cards, ARCnets use "shared memory" for copying buffers around. Make SURE it doesn't conflict with any other used memory in your system! A0000 - VGA graphics memory (ok if you don't have VGA) B0000 - Monochrome text mode C0000 \ One of these is your VGA BIOS - usually C0000. E0000 / F0000 - System BIOS Anything less than 0xA0000 is, well, a BAD idea since it isn't above 640k. - Avery's favourite: 0xD0000 - the station address: Every ARCnet card has its own "unique" network address from 0 to 255. Unlike ethernet, you can set this address yourself. Since it's only 8 bits, you can only have 254 ARCnet cards on a network. DON'T use 0 or 255, since these are reserved. (although neat stuff will probably happen if you DO use them). By the way, if you haven't already guessed, don't set this the same as any other ARCnet on your network! - Avery's favourite: 3 and 4. Not that it matters. ** Standard Microsystems Corp (SMC) ** PC100, PC110, PC120, PC130 (8-bit cards) PC500, PC600 (16-bit cards) --------------------------------- - mainly from Avery Pennarun - values depicted are from Avery's setup. - special thanks to Timo Hilbrink for noting that PC120, 130, 500, and 600 all have the same switches as Avery's PC100. PC500/600 have several extra, undocumented pins though. (?) - PC110 settings were verified by Stephen A. Wood JP5 [|] : : : : (IRQ Setting) IRQ2 IRQ3 IRQ4 IRQ5 IRQ7 Put exactly one jumper on exactly one set of pins. 1 2 3 4 5 6 7 8 9 10 S1 /----------------------------------\ (I/O and Memory | 1 1 * 0 0 0 0 * 1 1 0 1 | addresses) \----------------------------------/ |--| |--------| |--------| (a) (b) (m) a: The first digit of the I/O address. Setting Value ------- ----- 00 0 01 1 10 2 11 3 b: The second digit of the I/O address. Setting Value ------- ----- 0000 0 0001 1 0010 2 ... ... 1110 E 1111 F The I/O address is in the form ab0. For example, if a is 0x2 and b is 0xE, the address will be 0x2E0. DO NOT SET THIS LESS THAN 0x200!!!!! m: The first digit of the memory address. Setting Value ------- ----- 0000 0 0001 1 0010 2 ... ... 1110 E 1111 F The memory address is in the form m0000. For example, if m is D, the address will be 0xD0000. DO NOT SET THIS TO C0000, F0000, OR LESS THAN A0000! 1 2 3 4 5 6 7 8 S2 /--------------------------\ (Station Address) | 1 1 0 0 0 0 0 0 | \--------------------------/ Setting Value ------- ----- 00000000 00 10000000 01 01000000 02 ... 01111111 FE 11111111 FF Note that this is binary with the digits reversed! DO NOT SET THIS TO 0 OR 255 (0xFF)! ***************************************************************************** ** Standard Microsystems Corp (SMC) ** PC130E/PC270E (8-bit cards) --------------------------- - from Juergen Seifert STANDARD MICROSYSTEMS CORPORATION (SMC) ARCNET(R)-PC130E/PC270E =============================================================== This description has been written by Juergen Seifert using information from the following Original SMC Manual "Configuration Guide for ARCNET(R)-PC130E/PC270 Network Controller Boards Pub. # 900.044A June, 1989" ARCNET is a registered trademark of the Datapoint Corporation SMC is a registered trademark of the Standard Microsystems Corporation The PC130E is an enhanced version of the PC130 board, is equipped with a standard BNC female connector for connection to RG-62/U coax cable. Since this board is designed both for point-to-point connection in star networks and for connection to bus networks, it is downwardly compatible with all the other standard boards designed for coax networks (that is, the PC120, PC110 and PC100 star topology boards and the PC220, PC210 and PC200 bus topology boards). The PC270E is an enhanced version of the PC260 board, is equipped with two modular RJ11-type jacks for connection to twisted pair wiring. It can be used in a star or a daisy-chained network. 8 7 6 5 4 3 2 1 ________________________________________________________________ | | S1 | | | |_________________| | | Offs|Base |I/O Addr | | RAM Addr | ___| | ___ ___ CR3 |___| | | \/ | CR4 |___| | | PROM | ___| | | | N | | 8 | | SOCKET | o | | 7 | |________| d | | 6 | ___________________ e | | 5 | | | A | S | 4 | |oo| EXT2 | | d | 2 | 3 | |oo| EXT1 | SMC | d | | 2 | |oo| ROM | 90C63 | r |___| 1 | |oo| IRQ7 | | |o| _____| | |oo| IRQ5 | | |o| | J1 | | |oo| IRQ4 | | STAR |_____| | |oo| IRQ3 | | | J2 | | |oo| IRQ2 |___________________| |_____| |___ ______________| | | |_____________________________________________| Legend: SMC 90C63 ARCNET Controller / Transceiver /Logic S1 1-3: I/O Base Address Select 4-6: Memory Base Address Select 7-8: RAM Offset Select S2 1-8: Node ID Select EXT Extended Timeout Select ROM ROM Enable Select STAR Selected - Star Topology (PC130E only) Deselected - Bus Topology (PC130E only) CR3/CR4 Diagnostic LEDs J1 BNC RG62/U Connector (PC130E only) J1 6-position Telephone Jack (PC270E only) J2 6-position Telephone Jack (PC270E only) Setting one of the switches to Off/Open means "1", On/Closed means "0". Setting the Node ID ------------------- The eight switches in group S2 are used to set the node ID. Each node attached to the network must have an unique node ID which must be different from 0. Switch 1 serves as the least significant bit (LSB). The node ID is the sum of the values of all switches set to "1" These values are: Switch | Value -------|------- 1 | 1 2 | 2 3 | 4 4 | 8 5 | 16 6 | 32 7 | 64 8 | 128 Some Examples: Switch | Hex | Decimal 8 7 6 5 4 3 2 1 | Node ID | Node ID ----------------|---------|--------- 0 0 0 0 0 0 0 0 | not allowed 0 0 0 0 0 0 0 1 | 1 | 1 0 0 0 0 0 0 1 0 | 2 | 2 0 0 0 0 0 0 1 1 | 3 | 3 . . . | | 0 1 0 1 0 1 0 1 | 55 | 85 . . . | | 1 0 1 0 1 0 1 0 | AA | 170 . . . | | 1 1 1 1 1 1 0 1 | FD | 253 1 1 1 1 1 1 1 0 | FE | 254 1 1 1 1 1 1 1 1 | FF | 255 Setting the I/O Base Address ---------------------------- The first three switches in switch group S1 are used to select one of eight possible I/O Base addresses using the following table Switch | Hex I/O 1 2 3 | Address -------|-------- 0 0 0 | 260 0 0 1 | 290 0 1 0 | 2E0 (Manufacturer's default) 0 1 1 | 2F0 1 0 0 | 300 1 0 1 | 350 1 1 0 | 380 1 1 1 | 3E0 Setting the Base Memory (RAM) buffer Address -------------------------------------------- The memory buffer requires 2K of a 16K block of RAM. The base of this 16K block can be located in any of eight positions. Switches 4-6 of switch group S1 select the Base of the 16K block. Within that 16K address space, the buffer may be assigned any one of four positions, determined by the offset, switches 7 and 8 of group S1. Switch | Hex RAM | Hex ROM 4 5 6 7 8 | Address | Address *) -----------|---------|----------- 0 0 0 0 0 | C0000 | C2000 0 0 0 0 1 | C0800 | C2000 0 0 0 1 0 | C1000 | C2000 0 0 0 1 1 | C1800 | C2000 | | 0 0 1 0 0 | C4000 | C6000 0 0 1 0 1 | C4800 | C6000 0 0 1 1 0 | C5000 | C6000 0 0 1 1 1 | C5800 | C6000 | | 0 1 0 0 0 | CC000 | CE000 0 1 0 0 1 | CC800 | CE000 0 1 0 1 0 | CD000 | CE000 0 1 0 1 1 | CD800 | CE000 | | 0 1 1 0 0 | D0000 | D2000 (Manufacturer's default) 0 1 1 0 1 | D0800 | D2000 0 1 1 1 0 | D1000 | D2000 0 1 1 1 1 | D1800 | D2000 | | 1 0 0 0 0 | D4000 | D6000 1 0 0 0 1 | D4800 | D6000 1 0 0 1 0 | D5000 | D6000 1 0 0 1 1 | D5800 | D6000 | | 1 0 1 0 0 | D8000 | DA000 1 0 1 0 1 | D8800 | DA000 1 0 1 1 0 | D9000 | DA000 1 0 1 1 1 | D9800 | DA000 | | 1 1 0 0 0 | DC000 | DE000 1 1 0 0 1 | DC800 | DE000 1 1 0 1 0 | DD000 | DE000 1 1 0 1 1 | DD800 | DE000 | | 1 1 1 0 0 | E0000 | E2000 1 1 1 0 1 | E0800 | E2000 1 1 1 1 0 | E1000 | E2000 1 1 1 1 1 | E1800 | E2000 *) To enable the 8K Boot PROM install the jumper ROM. The default is jumper ROM not installed. Setting the Timeouts and Interrupt ---------------------------------- The jumpers labeled EXT1 and EXT2 are used to determine the timeout parameters. These two jumpers are normally left open. Refer to the COM9026 Data Sheet for alternate configurations. To select a hardware interrupt level set one (only one!) of the jumpers IRQ2, IRQ3, IRQ4, IRQ5, IRQ7. The manufacturer's default is IRQ2. Configuring the PC130E for Star or Bus Topology ----------------------------------------------- The single jumper labeled STAR is used to configure the PC130E board for star or bus topology. When the jumper is installed, the board may be used in a star network, when it is removed, the board can be used in a bus topology. Diagnostic LEDs --------------- Two diagnostic LEDs are visible on the rear bracket of the board. The green LED monitors the network activity: the red one shows the board activity: Green | Status Red | Status -------|------------------- ---------|------------------- on | normal activity flash/on | data transfer blink | reconfiguration off | no data transfer; off | defective board or | incorrect memory or | node ID is zero | I/O address ***************************************************************************** ** Standard Microsystems Corp (SMC) ** PC500/PC550 Long Board (16-bit cards) ------------------------------------- - from Juergen Seifert STANDARD MICROSYSTEMS CORPORATION (SMC) ARCNET-PC500/PC550 Long Board ===================================================================== Note: There is another Version of the PC500 called Short Version, which is different in hard- and software! The most important differences are: - The long board has no Shared memory - On the long board the selection of the interrupt is done by binary coded switch, on the short board directly by jumper. This description has been written by Juergen Seifert using information from the following Original SMC Manual "Configuration Guide for SMC ARCNET-PC500/PC550 Series Network Controller Boards Pub. # 900.033 Rev. A November, 1989" ARCNET is a registered trademark of the Datapoint Corporation SMC is a registered trademark of the Standard Microsystems Corporation The PC500 is equipped with a standard BNC female connector for connection to RG-62/U coax cable. The board is designed both for point-to-point connection in star networks and for connection to bus networks. The PC550 is equipped with two modular RJ11-type jacks for connection to twisted pair wiring. It can be used in a star or a daisy-chained network. 1 0 9 8 7 6 5 4 3 2 1 6 5 4 3 2 1 ____________________________________________________________________ < | SW1 | | SW2 | | > |_____________________| |_____________| | < IRQ |I/O Addr | > ___| < CR4 |___| > CR3 |___| < ___| > N | | 8 < o | | 7 > d | S | 6 < e | W | 5 > A | 3 | 4 < d | | 3 > d | | 2 < r |___| 1 > |o| _____| < |o| | J1 | > 3 1 JP6 |_____| < |o|o| JP2 | J2 | > |o|o| |_____| < 4 2__ ______________| > | | | <____| |_____________________________________________| Legend: SW1 1-6: I/O Base Address Select 7-10: Interrupt Select SW2 1-6: Reserved for Future Use SW3 1-8: Node ID Select JP2 1-4: Extended Timeout Select JP6 Selected - Star Topology (PC500 only) Deselected - Bus Topology (PC500 only) CR3 Green Monitors Network Activity CR4 Red Monitors Board Activity J1 BNC RG62/U Connector (PC500 only) J1 6-position Telephone Jack (PC550 only) J2 6-position Telephone Jack (PC550 only) Setting one of the switches to Off/Open means "1", On/Closed means "0". Setting the Node ID ------------------- The eight switches in group SW3 are used to set the node ID. Each node attached to the network must have an unique node ID which must be different from 0. Switch 1 serves as the least significant bit (LSB). The node ID is the sum of the values of all switches set to "1" These values are: Switch | Value -------|------- 1 | 1 2 | 2 3 | 4 4 | 8 5 | 16 6 | 32 7 | 64 8 | 128 Some Examples: Switch | Hex | Decimal 8 7 6 5 4 3 2 1 | Node ID | Node ID ----------------|---------|--------- 0 0 0 0 0 0 0 0 | not allowed 0 0 0 0 0 0 0 1 | 1 | 1 0 0 0 0 0 0 1 0 | 2 | 2 0 0 0 0 0 0 1 1 | 3 | 3 . . . | | 0 1 0 1 0 1 0 1 | 55 | 85 . . . | | 1 0 1 0 1 0 1 0 | AA | 170 . . . | | 1 1 1 1 1 1 0 1 | FD | 253 1 1 1 1 1 1 1 0 | FE | 254 1 1 1 1 1 1 1 1 | FF | 255 Setting the I/O Base Address ---------------------------- The first six switches in switch group SW1 are used to select one of 32 possible I/O Base addresses using the following table Switch | Hex I/O 6 5 4 3 2 1 | Address -------------|-------- 0 1 0 0 0 0 | 200 0 1 0 0 0 1 | 210 0 1 0 0 1 0 | 220 0 1 0 0 1 1 | 230 0 1 0 1 0 0 | 240 0 1 0 1 0 1 | 250 0 1 0 1 1 0 | 260 0 1 0 1 1 1 | 270 0 1 1 0 0 0 | 280 0 1 1 0 0 1 | 290 0 1 1 0 1 0 | 2A0 0 1 1 0 1 1 | 2B0 0 1 1 1 0 0 | 2C0 0 1 1 1 0 1 | 2D0 0 1 1 1 1 0 | 2E0 (Manufacturer's default) 0 1 1 1 1 1 | 2F0 1 1 0 0 0 0 | 300 1 1 0 0 0 1 | 310 1 1 0 0 1 0 | 320 1 1 0 0 1 1 | 330 1 1 0 1 0 0 | 340 1 1 0 1 0 1 | 350 1 1 0 1 1 0 | 360 1 1 0 1 1 1 | 370 1 1 1 0 0 0 | 380 1 1 1 0 0 1 | 390 1 1 1 0 1 0 | 3A0 1 1 1 0 1 1 | 3B0 1 1 1 1 0 0 | 3C0 1 1 1 1 0 1 | 3D0 1 1 1 1 1 0 | 3E0 1 1 1 1 1 1 | 3F0 Setting the Interrupt --------------------- Switches seven through ten of switch group SW1 are used to select the interrupt level. The interrupt level is binary coded, so selections from 0 to 15 would be possible, but only the following eight values will be supported: 3, 4, 5, 7, 9, 10, 11, 12. Switch | IRQ 10 9 8 7 | ---------|-------- 0 0 1 1 | 3 0 1 0 0 | 4 0 1 0 1 | 5 0 1 1 1 | 7 1 0 0 1 | 9 (=2) (default) 1 0 1 0 | 10 1 0 1 1 | 11 1 1 0 0 | 12 Setting the Timeouts -------------------- The two jumpers JP2 (1-4) are used to determine the timeout parameters. These two jumpers are normally left open. Refer to the COM9026 Data Sheet for alternate configurations. Configuring the PC500 for Star or Bus Topology ---------------------------------------------- The single jumper labeled JP6 is used to configure the PC500 board for star or bus topology. When the jumper is installed, the board may be used in a star network, when it is removed, the board can be used in a bus topology. Diagnostic LEDs --------------- Two diagnostic LEDs are visible on the rear bracket of the board. The green LED monitors the network activity: the red one shows the board activity: Green | Status Red | Status -------|------------------- ---------|------------------- on | normal activity flash/on | data transfer blink | reconfiguration off | no data transfer; off | defective board or | incorrect memory or | node ID is zero | I/O address ***************************************************************************** ** PureData Corp ** PDI507 (16-bit card) -------------------- - from Mark Rejhon (slight modifications by Avery) - Send questions/suggestions/etc about this text to Mark. Jumpers: There is a jumper array at the bottom of the card, near the edge connector. This array is labelled J1. They control the IRQs and something else. Put only one jumper on the IRQ pins. IRQ2 - Use IRQ 2 (same as IRQ 9 as far as software is concerned) IRQ3 - Use IRQ 3 (used by COM2 or COM4 serial port if either exists) IRQ4 - Use IRQ 4 (used by COM1 or COM3 serial port if either exists) IRQ5 - Use IRQ 5 (used by LPT2 parallel port if one exists) IRQ6 - Use IRQ 6 (used by Floppy Disk Controller if one exists) IRQ7 - Use IRQ 7 (used by LPT1 parallel port if one exists) [Avery's note: This "unknown" set of two jumpers appears to be on all ARCnet cards by SMC as well. Putting jumpers on them seems to affect the status register, but only for the two "reserved" bits, ETS1 and ETS2. Any further information is welcome.] ET1 - What is this? (Not tested, no jumper put on it) ET2 - What is this? (Not tested, no jumper put on it) There is a J2 jumper on two pins. A jumper should be put on them, since it was already there when I got the card. I don't know what this jumper is for though. There is a two-jumper array for J3. I don't know what it is for, but there were already two jumpers on it when I got the card. It's a six pin grid in a two-by-three fashion. The jumpers were configured as follows: .-------. o | o o | :-------: ------> Accessible end of card with connectors o | o o | in this direction -------> `-------' There is also a J4 jumper on two pins. A jumper should be put on them, since it was already there when I got the card. I don't know what this jumper is for though. DIP Switches: The dip switches accessible on the accessible end of the card while it is installed, is used to set the arcnet address. There are 8 switches. Use an address from 1 to 254. Switch No. 12345678 Arcnet address ----------------------------------------- 00000000 FF (Don't use this!) 00000001 FE 00000010 FD .... 11111101 2 11111110 1 11111111 0 (Don't use this!) There is another dipswitch array of 8 switches at the top of the card. There are five labelled MS0-MS4 which seem to control the memory address, and another three labelled IO0-IO2 which seem to control the base I/O address of the card. This was difficult to test by trial and error, and the I/O addresses are in a weird order. This was tested by setting the DIP switches, rebooting the computer, and attempting to load ARCETHER at various addresses (mostly between 0x200 and 0x400). The address that caused the red transmit LED to blink, is the one that I thought works. Also, the address 0x3D0 seem to have a special meaning, since the ARCETHER packet driver loaded fine, but without the red LED blinking. I don't know what 0x3D0 is for though. I recommend using an address of 0x300 since Windows may not like addresses below 0x300. IO Switch No. 210 I/O address ------------------------------- 111 0x260 110 0x290 101 0x2E0 100 0x2F0 011 0x300 010 0x350 001 0x380 000 0x3E0 The memory switches set a reserved address space of 0x1000 bytes (0x100 segment units, or 4k). For example if I set an address of 0xD000, it will use up addresses 0xD000 to 0xD100. The memory switches were tested by booting using QEMM386 stealth, and using LOADHI to see what address automatically became excluded from the upper memory regions, and then attempting to load ARCETHER using these addresses. I recommend using an arcnet memory address of 0xD000, and putting the EMS page frame at 0xC000 while using QEMM stealth mode. That way, you get contiguous high memory from 0xD100 almost all the way the end of the megabyte. Memory Switch 0 (MS0) didn't seem to work properly when set to OFF on my card. It could be malfunctioning on my card. Experiment with it ON first, and if it doesn't work, set it to OFF. (It may be a modifier for the 0x200 bit?) MS Switch No. 43210 Memory address -------------------------------- 00001 0xE100 (guessed - was not detected by QEMM) 00011 0xE000 (guessed - was not detected by QEMM) 00101 0xDD00 00111 0xDC00 01001 0xD900 01011 0xD800 01101 0xD500 01111 0xD400 10001 0xD100 10011 0xD000 10101 0xCD00 10111 0xCC00 11001 0xC900 (guessed - crashes tested system) 11011 0xC800 (guessed - crashes tested system) 11101 0xC500 (guessed - crashes tested system) 11111 0xC400 (guessed - crashes tested system) ***************************************************************************** ** CNet Technology Inc. ** 120 Series (8-bit cards) ------------------------ - from Juergen Seifert CNET TECHNOLOGY INC. (CNet) ARCNET 120A SERIES ============================================== This description has been written by Juergen Seifert using information from the following Original CNet Manual "ARCNET USER'S MANUAL for CN120A CN120AB CN120TP CN120ST CN120SBT P/N:12-01-0007 Revision 3.00" ARCNET is a registered trademark of the Datapoint Corporation P/N 120A ARCNET 8 bit XT/AT Star P/N 120AB ARCNET 8 bit XT/AT Bus P/N 120TP ARCNET 8 bit XT/AT Twisted Pair P/N 120ST ARCNET 8 bit XT/AT Star, Twisted Pair P/N 120SBT ARCNET 8 bit XT/AT Star, Bus, Twisted Pair __________________________________________________________________ | | | ___| | LED |___| | ___| | N | | ID7 | o | | ID6 | d | S | ID5 | e | W | ID4 | ___________________ A | 2 | ID3 | | | d | | ID2 | | | 1 2 3 4 5 6 7 8 d | | ID1 | | | _________________ r |___| ID0 | | 90C65 || SW1 | ____| | JP 8 7 | ||_________________| | | | |o|o| JP1 | | | J2 | | |o|o| |oo| | | JP 1 1 1 | | | ______________ | | 0 1 2 |____| | | PROM | |___________________| |o|o|o| _____| | > SOCKET | JP 6 5 4 3 2 |o|o|o| | J1 | | |______________| |o|o|o|o|o| |o|o|o| |_____| |_____ |o|o|o|o|o| ______________| | | |_____________________________________________| Legend: 90C65 ARCNET Probe S1 1-5: Base Memory Address Select 6-8: Base I/O Address Select S2 1-8: Node ID Select (ID0-ID7) JP1 ROM Enable Select JP2 IRQ2 JP3 IRQ3 JP4 IRQ4 JP5 IRQ5 JP6 IRQ7 JP7/JP8 ET1, ET2 Timeout Parameters JP10/JP11 Coax / Twisted Pair Select (CN120ST/SBT only) JP12 Terminator Select (CN120AB/ST/SBT only) J1 BNC RG62/U Connector (all except CN120TP) J2 Two 6-position Telephone Jack (CN120TP/ST/SBT only) Setting one of the switches to Off means "1", On means "0". Setting the Node ID ------------------- The eight switches in SW2 are used to set the node ID. Each node attached to the network must have an unique node ID which must be different from 0. Switch 1 (ID0) serves as the least significant bit (LSB). The node ID is the sum of the values of all switches set to "1" These values are: Switch | Label | Value -------|-------|------- 1 | ID0 | 1 2 | ID1 | 2 3 | ID2 | 4 4 | ID3 | 8 5 | ID4 | 16 6 | ID5 | 32 7 | ID6 | 64 8 | ID7 | 128 Some Examples: Switch | Hex | Decimal 8 7 6 5 4 3 2 1 | Node ID | Node ID ----------------|---------|--------- 0 0 0 0 0 0 0 0 | not allowed 0 0 0 0 0 0 0 1 | 1 | 1 0 0 0 0 0 0 1 0 | 2 | 2 0 0 0 0 0 0 1 1 | 3 | 3 . . . | | 0 1 0 1 0 1 0 1 | 55 | 85 . . . | | 1 0 1 0 1 0 1 0 | AA | 170 . . . | | 1 1 1 1 1 1 0 1 | FD | 253 1 1 1 1 1 1 1 0 | FE | 254 1 1 1 1 1 1 1 1 | FF | 255 Setting the I/O Base Address ---------------------------- The last three switches in switch block SW1 are used to select one of eight possible I/O Base addresses using the following table Switch | Hex I/O 6 7 8 | Address ------------|-------- ON ON ON | 260 OFF ON ON | 290 ON OFF ON | 2E0 (Manufacturer's default) OFF OFF ON | 2F0 ON ON OFF | 300 OFF ON OFF | 350 ON OFF OFF | 380 OFF OFF OFF | 3E0 Setting the Base Memory (RAM) buffer Address -------------------------------------------- The memory buffer (RAM) requires 2K. The base of this buffer can be located in any of eight positions. The address of the Boot Prom is memory base + 8K or memory base + 0x2000. Switches 1-5 of switch block SW1 select the Memory Base address. Switch | Hex RAM | Hex ROM 1 2 3 4 5 | Address | Address *) --------------------|---------|----------- ON ON ON ON ON | C0000 | C2000 ON ON OFF ON ON | C4000 | C6000 ON ON ON OFF ON | CC000 | CE000 ON ON OFF OFF ON | D0000 | D2000 (Manufacturer's default) ON ON ON ON OFF | D4000 | D6000 ON ON OFF ON OFF | D8000 | DA000 ON ON ON OFF OFF | DC000 | DE000 ON ON OFF OFF OFF | E0000 | E2000 *) To enable the Boot ROM install the jumper JP1 Note: Since the switches 1 and 2 are always set to ON it may be possible that they can be used to add an offset of 2K, 4K or 6K to the base address, but this feature is not documented in the manual and I haven't tested it yet. Setting the Interrupt Line -------------------------- To select a hardware interrupt level install one (only one!) of the jumpers JP2, JP3, JP4, JP5, JP6. JP2 is the default. Jumper | IRQ -------|----- 2 | 2 3 | 3 4 | 4 5 | 5 6 | 7 Setting the Internal Terminator on CN120AB/TP/SBT -------------------------------------------------- The jumper JP12 is used to enable the internal terminator. ----- 0 | 0 | ----- ON | | ON | 0 | | 0 | | | OFF ----- OFF | 0 | 0 ----- Terminator Terminator disabled enabled Selecting the Connector Type on CN120ST/SBT ------------------------------------------- JP10 JP11 JP10 JP11 ----- ----- 0 0 | 0 | | 0 | ----- ----- | | | | | 0 | | 0 | | 0 | | 0 | | | | | ----- ----- | 0 | | 0 | 0 0 ----- ----- Coaxial Cable Twisted Pair Cable (Default) Setting the Timeout Parameters ------------------------------ The jumpers labeled EXT1 and EXT2 are used to determine the timeout parameters. These two jumpers are normally left open. ***************************************************************************** ** CNet Technology Inc. ** 160 Series (16-bit cards) ------------------------- - from Juergen Seifert CNET TECHNOLOGY INC. (CNet) ARCNET 160A SERIES ============================================== This description has been written by Juergen Seifert using information from the following Original CNet Manual "ARCNET USER'S MANUAL for CN160A CN160AB CN160TP P/N:12-01-0006 Revision 3.00" ARCNET is a registered trademark of the Datapoint Corporation P/N 160A ARCNET 16 bit XT/AT Star P/N 160AB ARCNET 16 bit XT/AT Bus P/N 160TP ARCNET 16 bit XT/AT Twisted Pair ___________________________________________________________________ < _________________________ ___| > |oo| JP2 | | LED |___| < |oo| JP1 | 9026 | LED |___| > |_________________________| ___| < N | | ID7 > 1 o | | ID6 < 1 2 3 4 5 6 7 8 9 0 d | S | ID5 > _______________ _____________________ e | W | ID4 < | PROM | | SW1 | A | 2 | ID3 > > SOCKET | |_____________________| d | | ID2 < |_______________| | IO-Base | MEM | d | | ID1 > r |___| ID0 < ____| > | | < | J1 | > | | < |____| > 1 1 1 1 | < 3 4 5 6 7 JP 8 9 0 1 2 3 | > |o|o|o|o|o| |o|o|o|o|o|o| | < |o|o|o|o|o| __ |o|o|o|o|o|o| ___________| > | | | <____________| |_______________________________________| Legend: 9026 ARCNET Probe SW1 1-6: Base I/O Address Select 7-10: Base Memory Address Select SW2 1-8: Node ID Select (ID0-ID7) JP1/JP2 ET1, ET2 Timeout Parameters JP3-JP13 Interrupt Select J1 BNC RG62/U Connector (CN160A/AB only) J1 Two 6-position Telephone Jack (CN160TP only) LED Setting one of the switches to Off means "1", On means "0". Setting the Node ID ------------------- The eight switches in SW2 are used to set the node ID. Each node attached to the network must have an unique node ID which must be different from 0. Switch 1 (ID0) serves as the least significant bit (LSB). The node ID is the sum of the values of all switches set to "1" These values are: Switch | Label | Value -------|-------|------- 1 | ID0 | 1 2 | ID1 | 2 3 | ID2 | 4 4 | ID3 | 8 5 | ID4 | 16 6 | ID5 | 32 7 | ID6 | 64 8 | ID7 | 128 Some Examples: Switch | Hex | Decimal 8 7 6 5 4 3 2 1 | Node ID | Node ID ----------------|---------|--------- 0 0 0 0 0 0 0 0 | not allowed 0 0 0 0 0 0 0 1 | 1 | 1 0 0 0 0 0 0 1 0 | 2 | 2 0 0 0 0 0 0 1 1 | 3 | 3 . . . | | 0 1 0 1 0 1 0 1 | 55 | 85 . . . | | 1 0 1 0 1 0 1 0 | AA | 170 . . . | | 1 1 1 1 1 1 0 1 | FD | 253 1 1 1 1 1 1 1 0 | FE | 254 1 1 1 1 1 1 1 1 | FF | 255 Setting the I/O Base Address ---------------------------- The first six switches in switch block SW1 are used to select the I/O Base address using the following table: Switch | Hex I/O 1 2 3 4 5 6 | Address ------------------------|-------- OFF ON ON OFF OFF ON | 260 OFF ON OFF ON ON OFF | 290 OFF ON OFF OFF OFF ON | 2E0 (Manufacturer's default) OFF ON OFF OFF OFF OFF | 2F0 OFF OFF ON ON ON ON | 300 OFF OFF ON OFF ON OFF | 350 OFF OFF OFF ON ON ON | 380 OFF OFF OFF OFF OFF ON | 3E0 Note: Other IO-Base addresses seem to be selectable, but only the above combinations are documented. Setting the Base Memory (RAM) buffer Address -------------------------------------------- The switches 7-10 of switch block SW1 are used to select the Memory Base address of the RAM (2K) and the PROM. Switch | Hex RAM | Hex ROM 7 8 9 10 | Address | Address ----------------|---------|----------- OFF OFF ON ON | C0000 | C8000 OFF OFF ON OFF | D0000 | D8000 (Default) OFF OFF OFF ON | E0000 | E8000 Note: Other MEM-Base addresses seem to be selectable, but only the above combinations are documented. Setting the Interrupt Line -------------------------- To select a hardware interrupt level install one (only one!) of the jumpers JP3 through JP13 using the following table: Jumper | IRQ -------|----------------- 3 | 14 4 | 15 5 | 12 6 | 11 7 | 10 8 | 3 9 | 4 10 | 5 11 | 6 12 | 7 13 | 2 (=9) Default! Note: - Do not use JP11=IRQ6, it may conflict with your Floppy Disk Controller - Use JP3=IRQ14 only, if you don't have an IDE-, MFM-, or RLL- Hard Disk, it may conflict with their controllers Setting the Timeout Parameters ------------------------------ The jumpers labeled JP1 and JP2 are used to determine the timeout parameters. These two jumpers are normally left open. ***************************************************************************** ** No Name ** 8-bit cards, 16-bit cards ------------------------- - from Juergen Seifert NONAME 8-BIT ARCNET =================== I have named this ARCnet card "NONAME", since there is no name of any manufacturer on the Installation manual nor on the shipping box. The only hint to the existence of a manufacturer at all is written into copper, it is "Made in Taiwan" This description has been written by Juergen Seifert using information from the Original "ARCnet Installation Manual" ________________________________________________________________ | |STAR| BUS| T/P| | | |____|____|____| | | _____________________ | | | | | | | | | | | | | | | SMC | | | | | | | | COM90C65 | | | | | | | | | | | |__________-__________| | | _____| | _______________ | CN | | | PROM | |_____| | > SOCKET | | | |_______________| 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 | | _______________ _______________ | | |o|o|o|o|o|o|o|o| | SW1 || SW2 || | |o|o|o|o|o|o|o|o| |_______________||_______________|| |___ 2 3 4 5 7 E E R Node ID IOB__|__MEM____| | \ IRQ / T T O | |__________________1_2_M______________________| Legend: COM90C65: Arcnet Probe S1 1-8: Node ID Select S2 1-3: I/O Base Address Select 4-6: Memory Base Address Select 7-8: RAM Offset Select ET1, ET2 Extended Timeout Select ROM ROM Enable Select CN RG62 Coax Connector STAR| BUS | T/P Three fields for placing a sign (colored circle) indicating the topology of the card Setting one of the switches to Off means "1", On means "0". Setting the Node ID ------------------- The eight switches in group SW1 are used to set the node ID. Each node attached to the network must have an unique node ID which must be different from 0. Switch 8 serves as the least significant bit (LSB). The node ID is the sum of the values of all switches set to "1" These values are: Switch | Value -------|------- 8 | 1 7 | 2 6 | 4 5 | 8 4 | 16 3 | 32 2 | 64 1 | 128 Some Examples: Switch | Hex | Decimal 1 2 3 4 5 6 7 8 | Node ID | Node ID ----------------|---------|--------- 0 0 0 0 0 0 0 0 | not allowed 0 0 0 0 0 0 0 1 | 1 | 1 0 0 0 0 0 0 1 0 | 2 | 2 0 0 0 0 0 0 1 1 | 3 | 3 . . . | | 0 1 0 1 0 1 0 1 | 55 | 85 . . . | | 1 0 1 0 1 0 1 0 | AA | 170 . . . | | 1 1 1 1 1 1 0 1 | FD | 253 1 1 1 1 1 1 1 0 | FE | 254 1 1 1 1 1 1 1 1 | FF | 255 Setting the I/O Base Address ---------------------------- The first three switches in switch group SW2 are used to select one of eight possible I/O Base addresses using the following table Switch | Hex I/O 1 2 3 | Address ------------|-------- ON ON ON | 260 ON ON OFF | 290 ON OFF ON | 2E0 (Manufacturer's default) ON OFF OFF | 2F0 OFF ON ON | 300 OFF ON OFF | 350 OFF OFF ON | 380 OFF OFF OFF | 3E0 Setting the Base Memory (RAM) buffer Address -------------------------------------------- The memory buffer requires 2K of a 16K block of RAM. The base of this 16K block can be located in any of eight positions. Switches 4-6 of switch group SW2 select the Base of the 16K block. Within that 16K address space, the buffer may be assigned any one of four positions, determined by the offset, switches 7 and 8 of group SW2. Switch | Hex RAM | Hex ROM 4 5 6 7 8 | Address | Address *) -----------|---------|----------- 0 0 0 0 0 | C0000 | C2000 0 0 0 0 1 | C0800 | C2000 0 0 0 1 0 | C1000 | C2000 0 0 0 1 1 | C1800 | C2000 | | 0 0 1 0 0 | C4000 | C6000 0 0 1 0 1 | C4800 | C6000 0 0 1 1 0 | C5000 | C6000 0 0 1 1 1 | C5800 | C6000 | | 0 1 0 0 0 | CC000 | CE000 0 1 0 0 1 | CC800 | CE000 0 1 0 1 0 | CD000 | CE000 0 1 0 1 1 | CD800 | CE000 | | 0 1 1 0 0 | D0000 | D2000 (Manufacturer's default) 0 1 1 0 1 | D0800 | D2000 0 1 1 1 0 | D1000 | D2000 0 1 1 1 1 | D1800 | D2000 | | 1 0 0 0 0 | D4000 | D6000 1 0 0 0 1 | D4800 | D6000 1 0 0 1 0 | D5000 | D6000 1 0 0 1 1 | D5800 | D6000 | | 1 0 1 0 0 | D8000 | DA000 1 0 1 0 1 | D8800 | DA000 1 0 1 1 0 | D9000 | DA000 1 0 1 1 1 | D9800 | DA000 | | 1 1 0 0 0 | DC000 | DE000 1 1 0 0 1 | DC800 | DE000 1 1 0 1 0 | DD000 | DE000 1 1 0 1 1 | DD800 | DE000 | | 1 1 1 0 0 | E0000 | E2000 1 1 1 0 1 | E0800 | E2000 1 1 1 1 0 | E1000 | E2000 1 1 1 1 1 | E1800 | E2000 *) To enable the 8K Boot PROM install the jumper ROM. The default is jumper ROM not installed. Setting Interrupt Request Lines (IRQ) ------------------------------------- To select a hardware interrupt level set one (only one!) of the jumpers IRQ2, IRQ3, IRQ4, IRQ5 or IRQ7. The manufacturer's default is IRQ2. Setting the Timeouts -------------------- The two jumpers labeled ET1 and ET2 are used to determine the timeout parameters (response and reconfiguration time). Every node in a network must be set to the same timeout values. ET1 ET2 | Response Time (us) | Reconfiguration Time (ms) --------|--------------------|-------------------------- Off Off | 78 | 840 (Default) Off On | 285 | 1680 On Off | 563 | 1680 On On | 1130 | 1680 On means jumper installed, Off means jumper not installed NONAME 16-BIT ARCNET ==================== The manual of my 8-Bit NONAME ARCnet Card contains another description of a 16-Bit Coax / Twisted Pair Card. This description is incomplete, because there are missing two pages in the manual booklet. (The table of contents reports pages ... 2-9, 2-11, 2-12, 3-1, ... but inside the booklet there is a different way of counting ... 2-9, 2-10, A-1, (empty page), 3-1, ..., 3-18, A-1 (again), A-2) Also the picture of the board layout is not as good as the picture of 8-Bit card, because there isn't any letter like "SW1" written to the picture. Should somebody have such a board, please feel free to complete this description or to send a mail to me! This description has been written by Juergen Seifert using information from the Original "ARCnet Installation Manual" ___________________________________________________________________ < _________________ _________________ | > | SW? || SW? | | < |_________________||_________________| | > ____________________ | < | | | > | | | < | | | > | | | < | | | > | | | < | | | > |____________________| | < ____| > ____________________ | | < | | | J1 | > | < | | < |____________________| ? ? ? ? ? ? |____| > |o|o|o|o|o|o| | < |o|o|o|o|o|o| | > | < __ ___________| > | | | <____________| |_______________________________________| Setting one of the switches to Off means "1", On means "0". Setting the Node ID ------------------- The eight switches in group SW2 are used to set the node ID. Each node attached to the network must have an unique node ID which must be different from 0. Switch 8 serves as the least significant bit (LSB). The node ID is the sum of the values of all switches set to "1" These values are: Switch | Value -------|------- 8 | 1 7 | 2 6 | 4 5 | 8 4 | 16 3 | 32 2 | 64 1 | 128 Some Examples: Switch | Hex | Decimal 1 2 3 4 5 6 7 8 | Node ID | Node ID ----------------|---------|--------- 0 0 0 0 0 0 0 0 | not allowed 0 0 0 0 0 0 0 1 | 1 | 1 0 0 0 0 0 0 1 0 | 2 | 2 0 0 0 0 0 0 1 1 | 3 | 3 . . . | | 0 1 0 1 0 1 0 1 | 55 | 85 . . . | | 1 0 1 0 1 0 1 0 | AA | 170 . . . | | 1 1 1 1 1 1 0 1 | FD | 253 1 1 1 1 1 1 1 0 | FE | 254 1 1 1 1 1 1 1 1 | FF | 255 Setting the I/O Base Address ---------------------------- The first three switches in switch group SW1 are used to select one of eight possible I/O Base addresses using the following table Switch | Hex I/O 3 2 1 | Address ------------|-------- ON ON ON | 260 ON ON OFF | 290 ON OFF ON | 2E0 (Manufacturer's default) ON OFF OFF | 2F0 OFF ON ON | 300 OFF ON OFF | 350 OFF OFF ON | 380 OFF OFF OFF | 3E0 Setting the Base Memory (RAM) buffer Address -------------------------------------------- The memory buffer requires 2K of a 16K block of RAM. The base of this 16K block can be located in any of eight positions. Switches 6-8 of switch group SW1 select the Base of the 16K block. Within that 16K address space, the buffer may be assigned any one of four positions, determined by the offset, switches 4 and 5 of group SW1. Switch | Hex RAM | Hex ROM 8 7 6 5 4 | Address | Address -----------|---------|----------- 0 0 0 0 0 | C0000 | C2000 0 0 0 0 1 | C0800 | C2000 0 0 0 1 0 | C1000 | C2000 0 0 0 1 1 | C1800 | C2000 | | 0 0 1 0 0 | C4000 | C6000 0 0 1 0 1 | C4800 | C6000 0 0 1 1 0 | C5000 | C6000 0 0 1 1 1 | C5800 | C6000 | | 0 1 0 0 0 | CC000 | CE000 0 1 0 0 1 | CC800 | CE000 0 1 0 1 0 | CD000 | CE000 0 1 0 1 1 | CD800 | CE000 | | 0 1 1 0 0 | D0000 | D2000 (Manufacturer's default) 0 1 1 0 1 | D0800 | D2000 0 1 1 1 0 | D1000 | D2000 0 1 1 1 1 | D1800 | D2000 | | 1 0 0 0 0 | D4000 | D6000 1 0 0 0 1 | D4800 | D6000 1 0 0 1 0 | D5000 | D6000 1 0 0 1 1 | D5800 | D6000 | | 1 0 1 0 0 | D8000 | DA000 1 0 1 0 1 | D8800 | DA000 1 0 1 1 0 | D9000 | DA000 1 0 1 1 1 | D9800 | DA000 | | 1 1 0 0 0 | DC000 | DE000 1 1 0 0 1 | DC800 | DE000 1 1 0 1 0 | DD000 | DE000 1 1 0 1 1 | DD800 | DE000 | | 1 1 1 0 0 | E0000 | E2000 1 1 1 0 1 | E0800 | E2000 1 1 1 1 0 | E1000 | E2000 1 1 1 1 1 | E1800 | E2000 Setting Interrupt Request Lines (IRQ) ------------------------------------- ?????????????????????????????????????? Setting the Timeouts -------------------- ?????????????????????????????????????? ***************************************************************************** Other Cards ----------- I have no information on other models of ARCnet cards at the moment. Please send any and all info to: apenwarr@tourism.807-city.on.ca Thanks.